config NOE
#    bool "Ethernet GMAC"
    tristate
    depends on MS_NOE
    default MS_NOE
    help
      This driver support gigabit ethernet family of adapters.

if NOE

config NOE_FPGA_VERIFY
    bool

config NOE_NO_CHECK_ACTIVE_SETMAC
    bool "Not check active when setting MAC address"
    default y

choice
    prompt "GMAC1 is connected to"
    depends on NOE
    default GE1_GMII_AN_EXTPHY

config  GE1_GMII_AN_EXTPHY
    bool "GMII_AN (External GigaPhy)"

endchoice

config  MAC_TO_GIGAPHY_MODE_ADDR
    hex "GE1 Phy Address"
    default 0x1 if GE1_GMII_AN_EXTPHY


config NOE_GMAC2
    bool "GMAC2 Support"
    depends on NOE
    default y

choice
    prompt "GMAC2 is connected to"
    depends on NOE_GMAC2
    default GE2_GMII_AN_EXTPHY

config GE2_GMII_AN_EXTPHY
    bool "GMII (External GigaPhy)"
    depends on NOE_GMAC2
endchoice

config  MAC_TO_GIGAPHY_MODE_ADDR2
    hex "GE2 Phy Address"
    default 0x3 if GE2_GMII_AN_EXTPHY
    depends on NOE_GMAC2

config MDIO_IC1819
    bool "MDIO_IC1819 (SW MDIO TO CONTROL IC1819)"
    depends on NOE_GMAC2
    select MS_MDIO
    
config NOE_RGMII_TX_DELAY_2NS
    bool "RGMII tx delay 2ns default"
    depends on NOE
    default y

#choice
#    prompt "Network BottomHalves"
#    depends on NOE
#    default NOE_NETWORK_TASKLET_BH

config NOE_NETWORK_TASKLET_BH
#    bool "Tasklet"
    bool
    default n

config NOE_NETWORK_WORKQUEUE_BH
#    bool "Work Queue"
    bool
    default n

config NOE_NAPI
#    bool "NAPI"
    bool
    default y
#endchoice

#config NOE_SPECIAL_TAG
#   bool "Special Tag (0x810x)"
#   depends on NOE

config NOE_CHECKSUM_OFFLOAD
    bool
    default y
    depends on NOE

#config NOE_HW_IOCOHERENT
#    bool
#   default n
#   depends on NOE

config NOE_HW_LRO
#   bool "HW LRO"
    bool
    default y
    depends on NOE

config NOE_HW_VLAN_TX
    bool
    default y
    depends on NOE
    help
      Please disable HW_VLAN_TX if you need double vlan

config NOE_HW_VLAN_RX
    bool
    default n
    depends on NOE
    help
      Please disable HW_VLAN_RX if you need double vlan

config NOE_TSO
    bool
    default y
    depends on NOE_HW_VLAN_TX

config NOE_ETHTOOL
    select MII
    bool "support ethtool"
    default n
    depends on NOE

config NOE_QDMA
    bool "Choose QDMA istead PDMA"
    bool
    default y
    depends on NOE

config NOE_QDMATX_QDMARX
    bool
    depends on NOE_QDMA

config HW_SFQ
    bool
    depends on NOE_QDMA

config  ESW_DOUBLE_VLAN_TAG
    bool
    default n

config ETH_SKB_ALLOC_SELECT
    bool
    default y

#choice
#    prompt "SKB Allocation API Selection"
#    depends on ETH_SKB_ALLOC_SELECT
#    default ETH_SLAB_ALLOC_SKB

config  ETH_SLAB_ALLOC_SKB
    #bool "SLAB skb allocation"
    bool
    default y

config  ETH_PAGE_ALLOC_SKB
    #bool "Page skb allocation"
    bool
    default n

#endchoice

#config NOE_TX_RX_INT_SEPARATION
#    bool "Interrupt Separation"
#    default y


endif # NOE
